News

  • 36inch API 5L GR.B pipe export to Hongkong

    API 5L Carbon Steel Seamless Pipes is belongs to seamless pipe category . Mainly used in the mechanical structure, natural gas, oil, water transportation, chemical fertilizer equipment with boiler, petroleum cracking, geological drilling, oil drilling, etc.   API 5L pipes has seamless pipe ...
    Read more
  • MSS-SP-95 Swage Nipples

    MSS-SP-95 Swage Nipples

    Swage Nipples MSS-SP-95 BANGDONG manufactures, stocks and supplies a range of plain, bevelled and threaded concentric and eccentric swage nipples, from 8 (1⁄4″) NB to 100 (4″) NB, with other sizes available on request. All swage nipples are either manufactured from seamless pipe or bar material a...
    Read more
  • Standard and Material Of Fittings

    ASME: ANSI B16.9, ANSI B16.28, MSS-SP-43 DIN: DIN2605, DIN2615, DIN2616, DIN2617, DIN28011 EN: EN10253-1, EN10253-2 ASTM A403 – ASME SA403 – Standard Specification for Wrought Austenitic Stainless Steel Piping Fittings ASME B16.9 – Factory-Made Wrought Fittings Buttwelding ASME B16.25 – Buttweldi...
    Read more
  • Information Of Flanges

    Information Of Flanges

    Flanges are available various materials such as carbon steel, austenitic / martensitic / ferritic / duplex stainless steel, cast iron, aluminum, brass, bronze, plastic, etc. For specific services, flanges may be internally lined with protective materials (as pipes and fittings) or even painted e...
    Read more
  • What is the difference between lateral tee and True WYE

    We are manufacturer of Lateral Wye, Lateral Tee, true WYE and supply high quality Lateral Wye, Lateral Tee, true WYE in both large and small quantities worldwide & offer you the best prices in the market. We should analyze this from their shapes:the lateral tee divide two branch pipes:one is ...
    Read more
  • Export  seamless reduing tee to India

    Export seamless reduing tee to India

    Reducing tee Butt weld reducing tee has a branch that is smaller than main run. This allows for branching off to a smaller pipe of equipment from the main run. Reducing tee also called unequal tee  is a butt weld pipe fitting in which the branch port size is little than the parts of the run pipe...
    Read more
  • 3D Bend export To  Dammam

    3D Bend export To Dammam

    Pipe bending The pipe bending is used to change the direction of run of pipe. It advantage is can matach long distance transition requirements,so it is commonly that bends dimension according to customer design. ◦ASTM A234 WPB ◦ASME B16.9 ◦ASME B16.28 ◦ANSI/ASME B16.25 ◦MSS SP-97 Pipe bendi...
    Read more
  • The type of forged flange and sealing face for flange

    The type of forged flange and sealing face for flange

    The type of forged flange and sealing face for flange Different types of flange faces are used as the contact surfaces to seat the sealing gasket material. The type of flange The type of sealing face  Pressure Class(PN,MPA)  Plate flange(PL) Raise Face(RF) 0.25-2.5 Flat Face( FF) 0.25-1.6 ...
    Read more
  • Scrd Elbow dimension

    Scrd Elbow dimension

    2000 lbs FORGED ELBOW ASME B16.11-2008Forged Threaded Elbow Nominal Pipe Size Center-to-End OD of BandH Wall ThicknessG min Full LengthL min   Length of Thread Ltmin   DN NPT 90 Degree 45 Degree 2000LB 6 1/8 21 17 22 3.18 6.4 6.7 8 1/4 ...
    Read more
  • 4 Nps 90deg Elbow

    4 Nps 90deg Elbow

    Pipe Elbow dimensions are covered in ASME B16.9. Refer to the table given below for the size 1/2″ to 48″. NOMINAL PIPE SIZE OUTSIDE DIAMETER CENTER TO END Inch. OD A B C 1/2 21.3 38 16 – 3/4 26.7 29 11 – 1 33.4 38 22 25 1 1/4 42.2 48 25 32 1 1/2 48.3 57 29 38 2 60.3 76 35 51 ...
    Read more
  • Pipe Fastener Stud Bolt

    Pipe Fastener Stud Bolt

    Stud Bolt – A complete Guide of Pipe Fastener Stud bolt, nuts, machine bolts, and washers are also known as bolting material or fastener. Bolting is the term that used to tighten/create the flange joints connection. The tightening of the flange ensures the leak-proof connection...
    Read more
  • Pipe Tee Dimensions – Standard Reducing & Equal Tee

    Pipe Tee Dimensions – Standard Reducing & Equal Tee

    Pipe Tee Dimensions – Standard Reducing & Equal Tee Pipe Tee dimensions are covered in ASME B16.9. Refer to the table given below for the size 1/2″ to 48″. In piping two types of the tee are uses. Stright / equal and reducing tee. The following shall be checked during the in...
    Read more
123 Next > >> Page 1 / 3